This anaerobic adhesive kit from Corning Cable Systems are designed to work with anaerobic connectors. Please refer to the connectors department for Anaerobic Connectors info. Kit includes: 1. One 10ml Loctite 680 anaerobic adhesive (P/N: 680) 2. One 1.75 oz. Loctite 7649 primer N (P/N: 7649) 3. 10 pcs of 3cc syringes and needles This kit provides enough material for terminating more than 100 connectors.
Download Loctite 680 MSDS from here. Download Loctite 7649 MSDS from here.
Epo-Tek 353ND is a two component, heat curing epoxy designed for high temperature applications. It becomes a favorite epoxy of many fiber optic users. 353ND will perform continuously at 200°C and can endure 300~400°C for several minutes. It has excellent resistance to many types of solvents and chemicals and is ideal for bonding fiber optics, metals, glass, ceramics and most plastics. 353ND remains liquid until heat is applied. It can be applied by brush, dipping, pouring or mechanical dispensing techniques. This item comes in a 8oz kit with a shelf life of 1 year when stored at room temperature. Refrigeration is not required. Curing Schedule: 1 minute @150°C 2~5 minutes @120°C 5~10 minutes @100°C 15~30 minutes @80°C Pot Life: 4 hours Specifications: ...
This item comes in a 10ml bottle. LOCTITE® Product 680 is a high strength, single component anaerobic retaining adhesive for cylindrical joints. The product cures when confined in the absence of air between close fitting metal surfaces. This product is used on specially designed Anaerobic connectors. Please refer to our connectors department for more information about these connectors. 680 can be used with Loctite 7649 Primer N to increase cure speed. Direction of Use: Inject Loctite 680 into the connector with a syringe needle, dip or spray the fiber with Loctite 7649 (PN:7649) and connectorize as usual. Specifications: Chemical Type: Methacrylate Ester Appearance: Green Liquid Specific Gravity @ 25°C: 1.1 Viscosity @ 25°C, mPa.s (cP) Brookfield RVT Spindle 3 @ 20 ...
Loctite® HYSOL® 0151 is a clear two-component epoxy having optical clarity when used in small quantities. Hysol 0151 is easy to mix and has a 30 minutes pot life. It is excellent for general connector use. This item comes in a set of two separate tubes, each set weighs 3.3oz and 10 sets in a case. The price shown is for a case. NOTE: This item is considered hazardous material and GROUND shipment only. A UPS, FedEx or other carrier hazardous material handling fee will be added on each order. Cure Schedule: 24 hours @25°C 2 hours @60°C 1 hour @85°C 30 mins @120°C Pot Life: 100 grams, 60 minutes @25°C Specifications: Color: Milky White(Part A), Amber(Part B), Clear(Mixed) Mix Ratio: 100(A):33(B) by weight, 2.7(A):1(B) by volume Tg: 58°C ...
This item comes in a 1.75 fluid oz bottle. LOCTITE® ACTIVATOR 7649 Primer N is a single component non-CFC solvent based surface activator. The activator is designed to promote the speed of cure of Loctite anaerobic adhesives and sealants such as Loctite 680. 7649 can be used with Loctite 680 (PN:680) on specially designed Anaerobic connectors to increase the cure speed. Please refer to our connector department to get more information about these connectors. Direction for use: Inject the 680 Anaerobic adhesive into the connector with a syringe needle, dip or spray the fiber with primer 7649 and connectorize as usual. CAUTION: The activator is HIGHLY FLAMMABLE. UNDER NO CIRCUMSTANCES SHOULD ACTIVATOR AND ADHESIVE BE MIXED DIRECTLY AS LIQUIDS. This item is considered hazardous material and GROUND ...
The item is packaged in a 2 gram rigid plastic tube separated by a leak-proof clamp (BIPAX). Remove the clamp and mix right inside the BIPAX. This eliminates mix ratio errors with pre-measured resin and catalyst components.This package will prepare approximately 25~30 connectors. BAF110 is a rigid, optically clear adhesive with a very low viscosity. This room temperature curing system is an excellent choice for thin bond-line assembly and repair applications of prisms, lenses and other optic components. Its high strength makes this epoxy ideal for structural applications and its insulative properties are perfect for intricate bonding of electronic components. BAF110 exhibits excellent wetting and wicking capabilities which allows it to adhere strongly to glass, ceramics, metals and most rigid plastics. Its highly structured matrix gives BAF110 good resistance to salt ...
The item is packaged in a 2 gram rigid plastic tube separated by a leak-proof clamp (BIPAX). Remove the clamp and mix right inside the BIPAX. This eliminates mix ratio errors with pre-measured resin and catalyst components.This package will prepare approximately 25~30 connectors.
High Tg and Room Temperature Curing Fiber Optic Epoxy Adhesive
TRA-BOND F113SC is a room temperature curing, high Tg and low viscosity adhesive formulated for terminating ALL TYPES of fiber optic connectors. It has also been used for bonding LED displays, lenses and other optical components. TRA-BOND F113SC provides both high bond strength as well as low stress connections with no pistoning. This two part system can be cured overnight at room temperature or as quickly as 15 minutes at 90°C and is provided in a dark blue color to allow for easy polishing. ...
The item is packaged in a 2 gram rigid plastic tube separated by a leak-proof clamp (BIPAX). Remove the clamp and mix right inside the BIPAX. This eliminates mix ratio errors with pre-measured resin and catalyst components.This package will prepare approximately 25~30 connectors. BAF120 is a two-part, medium viscosity adhesive developed for high performance fiber optic and optical bonding applications. It is easily mixed and gels within minutes at room temperature for structural bonding applications where the combination of FAST CURE coupled with low shrinkage, good electrical insulation, and excellent mechanical properties is required. BAF120 is solvent "free" and is recommended for bonding fiber optic, optical and laser industry specified materilas including DuPont PIFAX plastic core or glass cables, single or multichannel terminations and connectors, and many other ...
The item is packaged in a 2 gram rigid plastic tube separated by a leak-proof clamp (BIPAX). Remove the clamp and mix right inside the BIPAX. This eliminates mix ratio errors with pre-measured resin and catalyst components. This package will prepare approximately 25~30 connectors. BAF253 is a low viscosity, high temperature, two-part epoxy formulation that changes color during the curing process to indicate cure status. The unmixed components are light yellow; the mixture is green/blue; and the fully cured adhesive is reddish-amber. It exhibits excellent wicking, and develops strong, tough mechanically stable bonds to a wide variety of fiber optic and optical materials that includes most metals, ceramics, glass and many plastics. In addition, BAF253 has good impact and thermal shock resistance, demonstrates low stress, and yields excellent pot and polish connections. ...
Email A Colleague